Ford

PAL Pro 39 Mechanics Truck

Ford F-550 Diesel
Stock number: PAL Pro 39-PSC 6025
  • Mechanics Truck
  • Available
  • IN STOCK

Offer information

Location details
5125 Clay Ave. SW | Grand Rapids, MI, 49548 - United States
Dealer details
Arista Truck Systems, Inc. | Contact: AJ DeLange
Dealer E-mail
sales@aristatrucksystems.com
Dealer phone
1-800-858-3659
Availability
Available
Product type
Mechanics Truck
Stock number
PAL Pro 39-PSC 6025

Crane body technical details

Palfinger Pal Pro 39-11 Galvaneal steel field service crane body

  • 11' long x 97.5" overall width
  • Entire body is epoxy primed and protected by submersion electro coat process.
  • Unlike spray systems, this ensures all surfaces including interior areas are protected.
  • 60" tall compartments on the front two compartments on the curbside and StreetSide.
  • Compartment outside depth is 22".
  • 50" wide treadplate cargo area floor.
  • Torsion box galvanized steel understructure. Eliminates truck & body deflection and twist.
  • Eight recessed, swiveling cargo tie downs in floor.
  • Designed for right rear crane mounting (up to a 39,000 ft. lb. crane rating).
  • 12 gauge, tread plate top on side packs with integrated full length drip rail over the doors.
  • Double panel doors with internal stiffeners, adhered with structural adhesive.
  • Doors constructed of high strength 5052-H32 aluminum.
  • Stainless-steel hinge with concealed leaves and full length rod type 7/16” diameter pins.
  • “T” handle latches with seal compression feature. Three point latch rods. Powder coated black.
  • Spring loaded, over center type door stops on all vertical doors.
  • Neoprene tubular door seals.
  • Swing out. Vertically hinged doors on horizontal compartments for better access.
  • 14” single handed slam operating type rear tailgate. With the Palfinger logo stamped.
  • 21” deep rear work bench bumper, with full through compartment.
  • 1/4"" thick smooth steel top with 3" overhang at rear for clamping items to the bench
  • Integrated left and right grip type steps for cargo area access.
  • Removable vise mounting bracket on the right rear corner.
  • Flexible step mounted under the driver side rear of the bumper with grab handle mounted on body.
  • Bumper is recessed and tapped to accept 2 2" receiver.
  • 2" receiver type hitch tube at the rear.
  • 7-way RV type trailer plug with flat terminals. Set up for combined brake & turn signals.
  • Rear fuel fill cut out with aluminum cup.
  • Full height aluminum rock chip protector on the of each side pack.

Drivers side compartments configured as follows:

1st vertical compartment
Heavy duty 250 lb. capacity C tech aluminum tool drawers with ball bearing roller slides.
5) 3” drawers in the street side front compartment. (Top of the stack )
2) 5” drawers in the street side front compartment. ( Middle of the stack )
1) 7” drawer in the street side front compartment. ( Bottom of the stack )

2nd vertical compartment.
Heavy duty 250 lb. capacity, C tech aluminum tool drawers with ball bearing roller slides.
5) 3” drawers in the street side front compartment. (Top of the stack )
2) 5” drawers in the street side front compartment. ( Middle of the stack )
1) 7” drawer in the street side front compartment. ( Bottom of the stack )

Horizontal compartment.
1) adjustable shelf with divider slots and 4 dividers.
Rear Vertical compartment.
1) adjustable shelves.

Passengers side compartments configured as follows:


1st vertical compartment.
Oxygen and Acetylene torch tank brackets in the front of the compartment.
Louvered compartment vent at bottom of compartment.
Vertical partition with 3 swivel hook in the rear of the compartment.
2nd vertical compartment.
2) adjustable shelves.

Horizontal compartment.
1) adjustable shelf with divider slots and 4 dividers.

Rear Vertical compartment.
Crane structure with air hose reel mounting shelf.
1/2” x 50’ hose reel in right rear compartment.
Hose access from back of body through a roller fairlead.
Moisture separator, oiler and regulator.

  • Automotive style sealed and integrated electrical system with central distribution point.
  • LED tail lights and marker lights.
  • Sealed plug in harness for the lights.
  • Body control system with power distribution boxes and control panels.
  • LED interior compartment lighting. Strip lighting along the sides and over the top of the door opening.
  • Four LED work lights.
    • 2) mounted on the rear of the body, one on each side facing the rear.
    • 2) mounted on the top of the body at the front, one on each side.
  • Rear and front stabilizers.
  • Manual out ( crane side only ) / power down stabilizers at the rear (both sides).
  • Integrated tapped mounting plates on the top of the body for air compressor, boom rest, welder, etc.
  • This eliminates the need for drilling holes through the top of the body which has potential for leaks.
  • Compressor mounting plates.
  • Boom rest mounting plates.
  • Miller welder mounting plate.

PAL Pro 39 Brochure Download

Service crane technical details

PAL Pro 6025 industrial field service crane

  • Palfinger crane mounting plate.
  • 38,500 ft. lb. rating.
  • Maintenance free, self aligning, hexagonal shaped boom with internal cylinders
  • All cylinders use a proprietary 5 stage marine grade seal system. ( Exceeds ANSI B30.5 )
  • 25' hydraulic reach from centerline of rotation.
  • 6,000 lbs. capacity @ 3' reach. / 1,380 lbs. capacity @ 25' reach.
  • 400 degree rotation.
  • Hydraulic powered planetary winch. Single line capacity 3,000 lbs. / double line 6,000 lbs.
  • Winch is mounted on the boom. Eliminates paying winch line out when raising or lowering boom.
  • 95’ of 5/16” wire rope.
  • Third wrap winch line limiting system. Ensures that at least three wraps remain on drum at all times.
  • Boom tip is clean and low profile. No anti two block bail and switch mechanism in the way.
  • Intelligent winch console. Proprietary damage protection system. No boom tip mechanisms.
  • Meets ANSI B30.5 standards
  • Radio remote hand held controller with push button switches.
  • Fully proportional hydraulic valves for fine movements.
  • Engine speed control at the remote control.
  • Engine kill at the remote control.
  • Overload shut down system.
  • Crane hook and snatch block.
  • Electric switch controls for hydraulic outriggers.
  • Boom support rest. Non-adjustable for 60" raised compartment option.
  • Installation labor
  • Crane components are grit blasted prior to paint finish process
  • Entire crane is epoxy primed and protected by submersion electro coat process.
  • Unlike spray systems, this ensures all surfaces including interior areas are protected.
  • Crane boom painted white with black cylinders.

PSC-6025 Brochure Download

Compressor technical details

Palfinger PRC 45V Rotary air compressor

  • Oil flooded rotary screw compressor. 46 cfm @ 150 PSI. delivery on demand air.
  • Integrated oil cooler with fan.
  • Mounted on compartment top behind driver.
  • Cold weather climate kit: includes ambient temp sensor and oil heater.
  • 6 gallon under body air tank with ball valve bleder for moisture
  • Compressor installation kit

Chassis details

Ford F-550 Diesel

  • Clear fram between cab and rear axle
  • 84" useable cab to axle
  • Note:  Chassis must be equipped with proper body builder interface circuit.
  • Live Drive transfer case replacement LDP-17-A electric shift transferase.
  • PTO with integrated pump for Ford automatic transmission.
  • Direct mount hydraulic pump
  • Hydraulic oil reservoir mounted in front of the bulkhead. 30 gallon capacity.
  • Ball shut off valves for maintenance or service.
  • Ford Super Duty adapter
  • Body to be painted white to match chassis

Similar products

  • Available
  • IN STOCK

PAL Pro 39 Mechanics Truck

2018 Ford F-550 XL
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

F550 SuperCab
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2019 Ford F-750
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

2019 Ford F-550
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2019 Peterbilt 337
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2018-2019 Kenworth T370
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 39 Mechanics Truck

2019 Ford F550 SuperCab 4x4 Diesel
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2019 Ford F750
  • Mechanics Truck
  • Available
  • IN STOCK
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2019 Kenworth T270
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 39 Mechanics Truck

2018 Ram 5500 Tradesman
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

2019 Ford F-550
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

Ram 5500 4x4 Regular Cap
  • Available
  • IN STOCK

Crane Body & Service Crane only

No Chassis
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

Ford F-750
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2019 Kenworth T370 |
  • Available
  • IN STOCK

PAL Pro 39 Mechanics Truck

2018 Ram 5500 Tradesman
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2019 Ford F-750
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

2019 Ford F-750
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

2019 Ford F550 4x4 SuperCab
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

F550 SuperCab
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

2019 Ford F-550
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 43 Mechanics Truck

2018 Ford F-550 SuperCab 4x4
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

F750 SuperCab
  • Mechanics Truck
  • Available
  • IN STOCK

PAL Pro 72 Mechanics Truck

F750 SuperCab
  • Mechanics Truck
  • Available
  • IN STOCK

PAL pro 43 Mechanics Truck

2019 Ford F-550